Фантекс XT View Ръководство за употреба за геймърско шаси тип Mid-Tower

1. Въведение

The Phanteks XT View is a mid-tower gaming chassis designed to accommodate modern hardware with enhanced cooling capabilities and internal space. It features tempered glass on both the front and side panels, allowing for a clear view of internal components. The chassis supports the latest mainboards with hidden rear connectors for a clean build aesthetic.

Image 1.1: Phanteks XT View Chassis with internal components and D-RGB lighting.

Ключови характеристики:

• Support for rear-side connector mainboards.
• Front and side tempered glass panels.
• Includes three M25-120mm D-RGB fans.
• Supports up to nine 120mm fan positions.
• Dedicated 360mm radiator support in the top panel.
• Accommodates large graphics cards.

2. Съдържание на пакета

Проверете дали всички компоненти са налични в опаковката:

• XT View Chassis (Black)
• Storage Bracket (1x)
• M25-120_DBK Fan (3x)
• D-RGB Controller (1x)
• Triple SSD Bracket (1x)
• Side D-RGB LED strip (1x)
• Accessory Box containing:
  • Връзки с цип (30x)
  • MB/SSD Screws (30x)
  • Винтове (4x)
  • HDD Screws (8x)
  • Standoff Tool (1x)
  • MB Standoff (1x)
  • PSU Screws (4x)
  • 30mm Fan Screws (12x, UNC6-32)

3. Настройка и инсталация

Follow these steps for proper assembly and installation of your PC components within the Phanteks XT View шаси.

3.1. Подготовка на шасито

1. Разопаковайте: Внимателно извадете шасито от опаковката му.
2. Премахване на панели: Unscrew and remove the tempered glass side panels and any other removable panels to access the interior.

Изображение 3.1: Интериор view of the XT View chassis, ready for component installation.

3.2. Инсталиране на дънната платка

1. Инсталирайте Standoffs: Ensure the correct standoffs are installed for your motherboard form factor (ATX, micro-ATX, mini-ITX, E-ATX). Use the included standoff tool if necessary.
2. Place Motherboard: Carefully align your motherboard with the standoffs and I/O shield opening.
3. Сигурна дънна платка: Use the provided MB screws to secure the motherboard to the chassis.

3.3. Монтаж на захранващ блок (PSU)

1. Position PSU: Slide the PSU into its designated compartment at the bottom rear of the chassis.
2. Secure PSU: Fasten the PSU to the chassis using the provided PSU screws.

3.4. Инсталиране на устройство за съхранение

The chassis supports 3.5" HDDs and 2.5" SSDs.

• 3.5" твърд диск: Install into the storage bracket. The chassis supports 2x 3.5" drives (or 1x if 2x SSDs are installed in the same bracket).
• 2.5" SSD: Install into the storage bracket or the triple SSD bracket. The chassis supports 2x 2.5" drives (or 0x if 2x HDDs are installed in the same bracket).

Secure drives with the appropriate screws.

3.5. Инсталиране на разширителна карта (GPU)

1. Премахване на капаците на слотовете: Отстранете необходимите капаци на слотовете за разширение от задната част на шасито.
2. Поставете карта: Carefully insert your graphics card or other expansion cards into the PCIe slots on the motherboard.
3. Сигурна карта: Fasten the expansion card with screws. Vertical GPU support is available with an optional bracket (PH-VGPUKT4.0_03R/PH-PGPUKT_01).

Изображение 3.2: Заден интериор view highlighting expansion slots and fan mounting points.

3.6. Монтаж на вентилатор и радиатор

The chassis supports various fan and radiator configurations:

• 120mm Fan Locations: Right Side (2x), Top (3x), Rear (1x), Midplate (3x).
• 140mm Fan Locations: Top (2x), Rear (1x).
• Liquid Cooling Radiator Support:
  • Side: Up to 240mm (with Vertical GPU only).
  • Top: Up to 360mm.
  • Rear: Up to 120mm.

Install the included M25-120 D-RGB fans in your preferred locations. Ensure proper airflow direction for optimal cooling.

3.7. Кабелно управление

Utilize the cable routing channels and tie-down points behind the motherboard tray to organize cables. This improves airflow and aesthetics.

Изображение 3.3: Задна част view illustrating cable management space.

3.8. Предни I/O връзки

Connect the front I/O cables from the chassis to the corresponding headers on your motherboard:

• USB 3.0 конектор
• USB-C 3.2 Gen2 Type-E header
• HD-Audio header
• Power switch, Reset button, D-RGB color button, D-RGB mode button headers
• D-RGB expansion header (for additional D-RGB devices)

4. Инструкции за работа

4.1. Включване/изключване

Натиснете Бутон за захранване located on the top front panel to turn the system on or off.

4.2. Свързване на предния панел

The front I/O panel provides convenient access to:

• 1x USB 3.0 порт
• 1x USB-C 3.2 Gen2 port
• Microphone/Headphone Combo jack

Image 4.1: Front I/O panel on the top of the chassis.

4.3. D-RGB Control

The integrated D-RGB controller allows for customization of the included D-RGB fans and LED strip. Use the D-RGB color button to cycle through colors and the D-RGB mode button to change lighting effects. The D-RGB system can also be synchronized with compatible motherboards via the D-RGB Motherboard connector.

5. Поддръжка

5.1. Почистване на прахоуловителни филтри

Regularly clean the dust filters to maintain optimal airflow and cooling performance. Dust filters are typically located at the front, top, and bottom of the chassis.

1. Премахване на филтри: Gently slide out or unclip the dust filters.
2. Чисто: Use compressed air or a soft brush to remove accumulated dust. For heavily soiled filters, wash with water and allow to dry completely before reinstallation.
3. Преинсталирайте: Place the clean, dry filters back into their positions.

5.2. Общо почистване

For external surfaces, use a soft, damp cloth to wipe down the chassis. Avoid abrasive cleaners or solvents that may damage the finish or tempered glass.

6. Отстраняване на проблеми

Този раздел разглежда често срещани проблеми, с които може да се сблъскате.

6.1. Системата не се включва

• Връзки за захранване: Verify that the PSU is properly connected to the wall outlet and the power switch on the PSU is in the 'ON' position.
• Връзки на дънната платка: Ensure all power cables from the PSU are securely connected to the motherboard (24-pin ATX, 8-pin CPU).
• Front Panel Header: Check that the power button cable from the front I/O is correctly connected to the motherboard's front panel header.

6.2. D-RGB Lighting Not Functioning

• D-RGB Controller Connection: Ensure the D-RGB controller is properly connected to the PSU and the D-RGB devices (fans, LED strip).
• Синхронизиране на дънната платка: If using motherboard D-RGB control, verify the D-RGB Motherboard cable is correctly connected and the motherboard's software is configured.
• Функционалност на бутона: Test the D-RGB color and mode buttons on the front panel.

6.3. Fan Noise or Malfunction

• Връзки: Ensure fan cables are securely connected to the motherboard fan headers or a fan controller.
• препятствия: Check for any cables or objects obstructing fan blades.
• Прах: Clean any dust buildup on fan blades.

7. Спецификации

8. Поддръжка и гаранция

For additional information, technical support, or warranty inquiries, please visit the official Phanteks webсайт:

www.phanteks.com

Refer to the Phanteks webза най-актуалните гаранционни условия, приложими за вашия регион.