PHILIPS ICN-2S28-N

Philips ICN-2S28-N Centium Electronic Ballast Instruction Manual

Model: ICN-2S28-N

1. Въведение

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Philips ICN-2S28-N Centium Electronic Ballast. This ballast is designed for use with two F28T5, F21T5, or F14T5 fluorescent lamps, and can also operate single lamps. Please read this manual thoroughly before installation and retain it for future reference.

2. Информация за безопасност

ПРЕДУПРЕЖДЕНИЕ: Risk of electric shock. Installation should be performed by a qualified electrician in accordance with all national and local electrical codes. Disconnect power at the circuit breaker before installation or servicing.

  • Уверете се, че захранването обtage matches the ballast's rated voltage (120V или 277V).
  • The ballast case must be properly grounded.
  • Монтирайте lamps within 1/4 inch of a grounded metal reflector.
  • Максимален обемtage for RED-BLUE leads is 500 Vrms.
  • Insulate YELLOW leads for 600V.
  • Only use rapid-start sockets with this ballast.
  • Do not modify the ballast or its wiring.
  • This ballast is a Semi-Conducteur, High Power Factor, Class P, Sound Rated A, Type 1 Outdoor, with Inherent Thermal Protection. It contains no PCB's.

3. Съдържание на пакета

Преди да започнете монтажа, проверете дали всички компоненти са налични:

  • 1 x Philips ICN-2S28-N Centium Electronic Ballast
Philips ICN-2S28-N Centium Electronic Ballast with integrated wiring

Image 1: Philips ICN-2S28-N Centium Electronic Ballast with its integrated wiring.

4. Настройка и инсталиране

Follow these steps for proper installation of the ballast:

  1. Изключете захранването: Before starting any work, ensure the main power supply to the fixture is turned off at the circuit breaker.
  2. Mount the Ballast: Securely mount the Philips ICN-2S28-N ballast within the fixture. Ensure the ballast case is grounded.
  3. Кабелни връзки: Refer to the wiring diagram on the ballast label and the instructions below.
Close-up of Philips ICN-2S28-N ballast label showing wiring diagram and specifications

Изображение 2: Подробности view of the ballast label, including wiring diagram and technical specifications.

Wiring Diagram Details:

  • Input Power (120V or 277V):
    • Свържете ЧЕРЕН wire to the Line (L) input.
    • Свържете БЯЛ wire to the Neutral (N) input.
  • Lamp Connections (for 2 Lampс):
    • Свържете СИН wires to one end of each lamp.
    • Свържете ЧЕРВЕНО wires to the other end of each lamp.
    • Свържете ЖЪЛТ wires to the remaining terminals of the lamps.
  • Заземяване: Ensure the ballast case is properly grounded to the fixture's metal housing.

Важни бележки:

  • This ballast is compatible with (2) F28T5, (2) F21T5, and (2) F14T5 lamps. It also works for single lamps.
  • Монтирайте lamps within 1/4 inch of a grounded metal reflector for optimal performance and safety.
  • Insulate any unused YELLOW leads for 600V.
  • Only use rapid-start sockets.
Philips ICN-2S28-N ballast with wires spread out, showing color coding

Image 3: The ballast with its color-coded wires clearly visible for connection.

5. Операция

Once the Philips ICN-2S28-N Centium Electronic Ballast is correctly installed and wired, operation is straightforward:

  1. After completing the installation, restore power to the circuit at the breaker.
  2. Turn on the light switch connected to the fixture. The ballast will automatically ignite and regulate the power to the fluorescent lamps.
  3. The ballast is designed for programmed start, ensuring optimal lamp живот.

6. Поддръжка

The Philips ICN-2S28-N Centium Electronic Ballast is designed for long-term, reliable operation with minimal maintenance. However, periodic checks can help ensure continued performance:

  • Изключване на захранването: Винаги изключвайте захранването, преди да извършвате каквато и да е поддръжка или проверка.
  • Почистване: Keep the ballast and fixture free from dust and debris to ensure proper heat dissipation. Use a dry, soft cloth for cleaning.
  • Проверка на окабеляването: Periodically inspect wiring connections for any signs of wear, fraying, or loose connections. Ensure all connections remain secure.
  • Lamp Замяна: При смяна на lamps, ensure they are of the correct type and wattage as specified for this ballast (F28T5, F21T5, F14T5).
  • Условия на околната среда: Ensure the ballast operates within its specified temperature range and environmental conditions (Type 1 Outdoor).

7. Отстраняване на проблеми

If your fluorescent fixture is not operating correctly, consult the following troubleshooting guide:

проблемВъзможна причинаРешение
Lamps не светят.Няма захранване на устройството.
Неправилно окабеляване.
Дефектен лamps.
Дефектен баласт.		Проверете предпазителя и стенния превключвател.
Verify all wiring connections against the diagram.
Заменете lamps with new ones of the correct type.
Ако лamps are new and wiring is correct, replace the ballast.
Lamps flicker or dim.Разхлабени кабелни връзки.
Неправилно лamp тип.
Стареене lamps.
Баластът наближава края на експлоатационния си живот.		Проверете и осигурете всички кабелни връзки.
Уверете се, че lamp types (F28T5, F21T5, F14T5) are used.
Заменете lamps.
Помислете за подмяна на баласта.
Ballast makes humming noise.Normal operation (slight hum).
Разхлабен монтаж.
Прегряване.		A slight hum is normal for some ballasts. Ensure ballast is securely mounted.
Check for proper ventilation and ensure ballast is not covered. If hum is loud or new, inspect for issues.

If troubleshooting steps do not resolve the issue, contact a qualified electrician or Philips customer support.

8. Спецификации

Below are the technical specifications for the Philips ICN-2S28-N Centium Electronic Ballast:

  • Номер на модела: ICN-2S28-N
  • марка: PHILIPS (Advance Ballast)
  • Входен обемtage: 120V / 277V
  • Съвместим Lamps: (2) F28T5, (2) F21T5, (2) F14T5 (also works for single lamps)
  • Уотtage: 28 watts (for F28T5 lamps)
  • Тип на източника на светлина: Флуоресцентни
  • Източник на захранване: Електрически с кабел
  • материал: Пластмаса
  • цвят: черен
  • форма: Правоъгълна
  • Тип завършване: черен
  • Тип монтаж: Поставка за багажник
  • Тегло на артикула: 9.6 унции
  • Размери на артикула (Д x Ш x В): 9.5" x 1.25" x 1"
  • UPC: 781087080726
  • Сертификати: UL Listed 704G, CSA (NRTL/C)
  • Характеристики: IntelliVolt (120V to 277V 50/60Hz), Programmed Start, High Power Factor, Class P, Sound Rated A, Type 1 Outdoor, Inherent Thermal Protection, No PCB's.
отстрани view of Philips ICN-2S28-N ballast showing dimensions and mounting holes

Изображение 4: Отстрани view of the ballast, illustrating its compact dimensions and mounting points.

9. Гаранция и поддръжка

This Philips ICN-2S28-N Centium Electronic Ballast comes with a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or contact Philips customer support.

For technical assistance or support, please contact Philips directly. Technical information is often available via their official webсайт или като се обадите на тяхната линия за поддръжка.

  • производител: Advance Ballast (a Philips company)
  • Техническа информация: 1.800.372.3331 (as seen on product label)
  • Онлайн помощ: Посетете официалния магазин на Philips website for product support and resources.

© 2024 PHILIPS. Всички права запазени. Информацията в това ръководство може да бъде променена без предупреждение.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.