Въведение
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Информация за безопасност
- Не излагайте скенера на екстремни температури, влажност или пряка слънчева светлина.
- Avoid dropping the scanner or subjecting it to severe impacts.
- Do not attempt to open or modify the scanner. Refer all servicing to qualified personnel.
- Use only the power supply and cables provided or approved by Intermec.
- Keep the scanning window clean to ensure accurate barcode reading.
Съдържание на пакета
Проверете дали вашият пакет съдържа следните елементи:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- Захранващ блок
- Documentation (this manual or similar)
Ако някои от артикулите липсват или са повредени, моля, свържете се незабавно с вашия доставчик.
Настройка
1. Свързване на скенера
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Свързване със скенера: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Свържете захранването: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Първоначално включване
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Работа със скенера
1. Сканиране на баркодове
- Цел: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- сканиране: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Потвърждение: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Разбиране на индикаторите
- Зелен светодиод: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Поддръжка
Почистване на скенера
- Regularly clean the scanning window with a soft, lint-free cloth dampс вода или мек, неабразивен почистващ препарат.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Уверете се, че скенерът е изключен, преди да го почистите.
Съхранение
Когато не се използва, съхранявайте скенера на чисто и сухо място, далеч от пряка слънчева светлина и екстремни температури.
Отстраняване на неизправности
| проблем | Възможна причина | Решение |
|---|---|---|
| Скенерът не се включва. | Захранващият кабел не е свързан; електрическият контакт е повреден; захранващият блок е повреден. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Скенерът не чете баркодове. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Спецификации
- модел: SR30
- Номер на част: 225-727-003 (Kit)
- Тип скенер: Линеен имиджър
- Интерфейс: RS232
- производител: Интермек
- Тегло на артикула: 0.01 ounces (approximate, scanner only)
- Отдел: Баркод
- ASIN: B003T0WF3S
Гаранция и поддръжка
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webсайт. Запазете касовата си бележка като доказателство за покупка при гаранционни рекламации.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.
