1. Въведение
This manual provides instructions for the proper installation and use of the Morris Products 15067 90 Degree Flex Duplex Box Connector. This connector is designed for connecting two pieces of flexible metallic conduit (FMC), AC, MC, or NM sheathed cable to a steel box or other metal enclosure using a single knockout opening.
Image: Two Morris Products 15067 90 Degree Flex Duplex Box Connectors. These zinc die-cast connectors feature a 90-degree bend, designed for connecting two pieces of flexible metallic conduit or various types of sheathed cables to an electrical box.
2. Какво има в кутията
The Morris Products 15067 package typically includes:
- Two (2) 3/8" Duplex 90 Degree Connectors (Model 15067)
3. Спецификации
| Характеристика | детайл |
|---|---|
| Номер на модела | 15067 |
| Тип конектор | 90 Degree Flex Duplex Box Connector |
| Материал | Цинкова отливка |
| Търговски размер | 3/8" FMC (fits 1/2" knockout) |
| Screw Design | 2 Screw design, Combo Head Screws |
| Applicable Cables | Flexible Metallic Conduit, AC, MC, NM sheathed cable |
| NM Cable Compatibility | 14/2 Thru 12/3 NM |
| AC Cable Compatibility | 14/2 Thru 10/4 AC |
| MC Cable Compatibility | 14/2 Thru 10/3 MC |
| Сертификати | cULus изброени |
| Размери на продукта | 4 x 6 x 12 инча |
| Тегло | 0.32 унции |
4. Инструкции за инсталиране
The Morris Products 15067 connector is designed for use in dry locations to connect two pieces of flexible metallic conduit or various types of sheathed cables to a steel outlet box or other metal enclosure.
Необходими инструменти (не са включени):
- Screwdriver (compatible with combo head screws)
- Wire strippers/cutters (as needed for cable preparation)
- Pliers or wrench (for tightening locknut, if applicable)
Стъпки на инсталиране:
- Подгответе корпуса: Ensure the steel box or metal enclosure has a 1/2" knockout opening available for the connector. Remove the knockout if not already done.
- Prepare the Cables: For each of the two cables (Flexible Metallic Conduit, AC, MC, or NM sheathed cable) to be connected, prepare the ends according to standard electrical practices, ensuring proper length and removal of outer sheathing as required for connection.
- Insert Cables into Connector: Loosen the two combo head screws on the connector. Insert one prepared cable end into each of the two openings of the 90-degree duplex connector. Ensure the cables are fully seated within the connector's clamps.
- Сигурни кабели: Tighten the two combo head screws firmly to secure both cables within the connector. Do not overtighten, but ensure a secure grip to prevent cable pull-out.
- Attach Connector to Enclosure: Insert the threaded end of the connector through the 1/2" knockout opening in the steel box or metal enclosure.
- Защитен конектор: Thread the locknut (if supplied separately or integrated) onto the threaded end of the connector from inside the enclosure and tighten it securely to fasten the connector to the box.
- Окончателна проверка: Verify that both cables are securely held by the connector and that the connector is firmly attached to the enclosure. Ensure all connections comply with local electrical codes.
5. Инструкции за работа
The Morris Products 15067 connector is a passive component designed to facilitate secure electrical connections. Once properly installed as per the installation instructions, it operates by maintaining the physical and electrical integrity of the cable connections to the enclosure. No ongoing operational steps are required beyond initial installation.
Важно: Ensure all electrical work is performed by qualified personnel and adheres to all applicable national and local electrical codes.
6. Поддръжка
The Morris Products 15067 90 Degree Flex Duplex Box Connector is a low-maintenance component. Once installed correctly, it typically requires no routine maintenance.
Периодични проверки:
- Визуална проверка: Periodically inspect the connector and surrounding cables for any signs of physical damage, corrosion, or loosening.
- Стегнатост: If accessible and safe to do so (with power disconnected), occasionally check the tightness of the screws securing the cables and the locknut securing the connector to the box. Retighten if necessary.
Забележка: Always disconnect power before performing any inspection or maintenance on electrical components.
7. Отстраняване на проблеми
Most issues related to the Morris Products 15067 connector stem from improper installation. Review the installation steps carefully if you encounter problems.
| проблем | Възможна причина | Решение |
|---|---|---|
| Cables are loose in the connector. | Винтовете не са затегнати достатъчно. | Ensure power is off. Retighten the two combo head screws on the connector firmly. |
| Connector is loose on the enclosure. | Locknut not tightened properly. | Ensure power is off. Tighten the locknut on the threaded end of the connector from inside the enclosure. |
| Cannot insert cable into connector. | Screws not loosened enough; incorrect cable type/size. | Ensure screws are fully loosened. Verify cable type and size are compatible with the connector's specifications (e.g., 14/2 Thru 12/3 NM, 14/2 Thru 10/4 AC, 14/2 Thru 10/3 MC). |
| Connector does not fit knockout. | Incorrect knockout size. | This 3/8" FMC connector is designed to fit a 1/2" knockout. Ensure the knockout size is correct. |
Ако проблемите продължават или не сте сигурни относно някоя от електрическите работи, консултирайте се с квалифициран електротехник.
8. Гаранция и поддръжка
For warranty information and technical support regarding Morris Products, please refer to the official Morris Products webсайт или се свържете директно с отдела за обслужване на клиенти. Запазете касовата си бележка за покупка за гаранционни рекламации.
Morris Products Contact Information:
- Webсайт: www.morrisproducts.com (Забележка: Това е заместител URL, please verify the actual manufacturer's webсайт за поддръжка.)
- Обслужване на клиенти: Обърнете се към website for contact numbers or email support.
