Въведение
Wampler Catacombs is a programmable, all-in-one delay and reverb pedal designed to provide a wide range of time-based effects for musicians. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your Catacombs pedal.
Продуктът е свършилview
The Catacombs pedal integrates 11 popular delay and reverb sounds into a single, intuitive unit. It features studio-quality 48 kHz sampling rate with 24-bit audio conversion, 8 onboard preset locations, and MIDI compatibility for up to 128 total presets.
Фигура 1: Отпред view на Wampler Catacombs pedal, showing controls for delay and reverb effects, input/output jacks, and footswitches.
Фигура 2: Под ъгъл view на Wampler Catacombs pedal, highlighting its compact design and various control knobs.
Настройка
Изисквания за захранване
Wampler Catacombs pedal requires a standard 9V DC power supply (not included) with a center-negative barrel connector. Ensure the power supply provides sufficient current for optimal performance.
Свързване на вашия педал
- Свържете инструмента си (например китара) към MONO IN or СТЕРЕО ВХОД жак от дясната страна на педала, като използвате стандартен 1/4-инчов инструментален кабел.
- Свържете МОНО ИЗХОД or STEREO OUT крик от лявата страна на педала към вашия amplifier or next effect pedal.
- Connect the 9V DC power supply to the 9V DC входен жак.
- For MIDI control, connect a MIDI cable to the MIDI вход.
Инструкция за работа
Контроли надview
- Delay Type Knob: Selects between various delay types including Tape, SPC, FTE, BBD, ANLG, and DIGI.
- Reverb Type Knob: Selects between reverb types such as SHMR (Shimmer), PLT (Plate), SPR (Spring), ROOM, and HALL.
- Time/Shimmer Knob: Adjusts the delay time or shimmer intensity depending on the selected effect.
- Feedback/Decay Knob: Controls the number of delay repeats or the reverb decay time.
- Mod Rate Knob: Adjusts the modulation rate for effects with modulation.
- Delay Tone Knob: Shapes the tone of the delay repeats.
- Reverb Tone Knob: Shapes the tone of the reverb effect.
- Bypass/ALT Footswitch: Toggles the effect on/off. Hold to access alternate functions (ALT mode).
- Preset/Save Footswitch: Cycles through presets. Hold to save current settings to a preset location.
- Tap Tempo Footswitch: Taps in the desired delay tempo.
Запазване и извикване на предварително зададени настройки
The Catacombs pedal allows for 8 onboard preset locations. To save a preset, adjust the knobs to your desired sound, then press and hold the Preset/Save footswitch until the indicator lights confirm the save. To recall a preset, short press the Preset/Save footswitch to cycle through the saved locations.
Alternate Functions (ALT Mode)
Some knobs have alternate functions accessible by holding the Bypass/ALT footswitch. When in ALT mode, the indicator light will change (e.g., from blue to red as noted in some user feedback), allowing you to adjust secondary parameters. Release the footswitch to return to normal operation.
Поддръжка
To ensure the longevity and optimal performance of your Wampler Catacombs pedal, follow these maintenance guidelines:
- Keep the pedal clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Съхранявайте педала на хладно и сухо място, далеч от пряка слънчева светлина и екстремни температури.
- Изключвайте захранването, когато не го използвате за продължителни периоди.
- Редовно проверявайте всички кабелни връзки за надеждно закрепване.
Отстраняване на неизправности
| проблем | Възможна причина | Решение |
|---|---|---|
| Няма звук при натискане на педала. | Incorrect power supply, faulty cables, incorrect input/output connections. | Verify power supply is 9V DC center-negative. Check all instrument cables. Ensure input is connected to IN and output to OUT. |
| Ефектът е или твърде фин, или твърде силен. | Knobs are set incorrectly, or in ALT mode unintentionally. | Adjust the relevant control knobs (Time, Feedback, Tone). Check if the pedal is in ALT mode and adjust accordingly. |
| Cannot save or recall presets. | Неправилна работа с педалния превключвател. | Уверете се, че държите Preset/Save footswitch long enough to save. For recalling, use short presses. |
| Шум или бръмчене. | Заземяващ контур, дефектно захранване, смущения. | Use an isolated power supply. Try different cables. Ensure proper grounding of all equipment. |
Спецификации
- модел: CATACOMBS
- Размери: 7.25 x 5.7 x 3.75 инча
- Тегло на артикула: 1.39 паунда
- Източник на захранване: Corded Electric (9V DC, center-negative, power supply not included)
- Формат на сигнала: Аналогов
- Audio Output Effects: Закъснение, Реверберация
- Sampлинг процент: 48 kHz
- Audio Bit Depth: 24-битов
- Предварителни настройки: 8 onboard, 128 via MIDI
- Manufacture Location: Designed and Built in the USA
Гаранция и поддръжка
Wampler Pedals products are designed and built to high standards. For warranty information and technical support, please refer to the official Wampler педали webсайта или се свържете директно с отдела за обслужване на клиенти. Запазете доказателството си за покупка за гаранционни рекламации.
За допълнителна помощ посетете Wampler Store on Amazon.
